In the process of changing the clean coal tubes the employee flopped the gate from tube 2 to tube 1. EE hand and glove on right hand got caught on the flop gate handle and the tube. This resulted in a cut to hand. EE was taken to the hospital where ee received 8 stitches and returned to work. EE has missed no work.
Employee was pulling a wash down water hose up to the next floor of the prep plant by hand. The water hose slipped through right hand and a metal hose clamp pulled through their hand and cut the inside of the hand. Employee took themselves to the hospital and received 8 stitches. Employee returned to work that same evening and has missed no work.
Employee sprained lower back and right shoulder lifting to help install clean coal screens in the prep plan. Employee continued to work and went to the doctor on 08/15/2017 and was taken off from work until 08/29/2017.
Utility person lost control of personal vehicle due to brake failure & traveled over embankment for an extended distance, thereby receiving traumatic injury (fractured right tibia & contusions) as a result of the vehicular crash.
EE WAS LEAVING THE CONTROL ROOM IN THE PREP PLANT AND TURNED THE HANDLE WITH HIS RIGHT HAND AND PUSHED ON THE GLASS WINDOW IN THE DOOR WITH HIS LEFT HAND. THE WINDOW BROKE, CUTTING HIS LEFT WRIST.
EE was cleaning a supply building and a box of miscellaneous parts fell and struck him on the left little finger.
EE was throwing the flop gate in the prep plant. It became fouled, and he was shaking it with his left hand. When the flop gate freed, it caught his finger against a piece of angle iron, cutting it.
EE was helping set a re-tracker for a de-railed railroad car and the CSX employee dropped his side of the re-tracker, resulting in the re-tracker falling on EE's left ring finger cutting it.
EE was working on the 3rd floor of the Screening Plant. He was at the sizing grid and stepped on a piece of floor grating. The piece of grating gave way and EE fell approximately 12 ft. to the floor below.
Employees were sliding steel beams across the floor. Injured employee's end of the steel beam hit a pipe and moved to the left catching his left hand (middle finger) between the beam and the pipe.
EE WAS LIFTING A 50 LB. OF CAT FLOCK TO BE LOADED INTO A HOPPER, AND WHEN HE LIFTED ON THE BAG, HE FELT A SHARP PAIN IN HIS BACK AND ABDOMEN.
MATERIAL FROM PLANT FEED CHUTE FELL ONTO EMPLOYEE'S RIGHT KNEE WHILE HE WAS IN THE CHUTE CLEANING IT OUT. NOT REPORTED TO OFFICE UNTIL 3/2/06.
Employee was working on sump make up water lines when a pipe fell on his right hand cutting middle finger.
CONVEYOR STRUCTURE TURNED (ROLLED) ONTO IT'S SIDE DUE TO MATERIAL OVERLOAD ON WALKWAY (SLURRY PIPE). IT STRUCK VICTIM ON ARM. HE FELL BACK AND STRUCK METAL TRUCK BED. INJURED ARM & BACK.
Please see attached explaination for this injury.He have aggravated existing condition that had occurred 16 yrs earlier. He was not aware the because he injured himself on the job and lost for this injury that it is work-related and reportable to msha and insurance formerly.
Iron worker dropped hammer-struck victim on top of hard hat.
EE was working in the prep plant shop and when he lifted an electrical breaker box, he felt a sharp pain in his lower back.
EE WAS HELPING CHANGE A 40 HP ELECTRIC MOTOR IN PREP PLANT. THE MOTOR WAS ON A TOW-WHEEL DOLLY. MOTOR STARTED TO FALL OFF DOLLY. EE GRABBED IT TO STABILIZE IT AND STRAINED LOWER BACK.
EE WAS USING A HIGH PRESSURE WATER HOSE TO WASH THE FLOOR IN THE BASEMENT OF PREP PLANT. WHEN THE WATER WAS TURNED ON, THE PRESSURE CAUSED HIM TO LOOSE HIS BALANCE. HE FELL ONTO A CEMENT BEAM CAUSING PAIN IN RIB AREA.
EMPLOYEE WAS LIFTING A BAG OF FLOCK DUST WHEN HE FELT PAIN IN THE LOWER PART OF HIS STOMACH.
DRIVER HAD TO STOP ON HILL IN DOING SO DRIVER GOT TRUCK OUT OF BEAR THEN JUMP FROM TRUCK.