Central ShopCoal

Employee was lying on his back, micing bores on 12CM12 mainframe CM97. A gust of wind blew debris from yard into his right side of face and into his eye. Received prescription.

Employee was assisting in the turning over of the stage loader drive assembly. Employee had his hand on the drive as it turned. The drive was approximately 3/4 ways turned over when the unbolted deck plate turned loose, striking employee's left middle finger.

EE was bending and forming heavy gauge wire. The wire slipped and stuck in EE's hand, cutting him at the base of his left thumb.

Employee was climbing on forklift and twisted his left knee.

Employee had been welding on the canopy retainer rings on the shield job for North River. When employee moved the wire-welder, he felt a pain in his lower back and right shoulder.

Employee was taking chains off load on lowboy trailer. When he finished, he jumped down, off the trailer, and felt pain in heel of foot.

Employee was installing a tensioner cylinder in tailgate using a crane. He pushed on cylinder to line pinhole up and felt something in shoulder snap.

EE picked up box and felt a pop in his shoulder. EE started losing time on 5/12/11.

EE was heating and bending metal on the pan section so it could be bent back into place.

EE was cleaning weld splatter from inside the electrical panel with a grinder. The grinder slipped and struck back of right hand. Employee was wearing leather driving gloves. He was leaning deep inside the panel cleaning the back. The grinder was dropped when it cut his hand.

Employee was pulling on a staple puller and the puller slipped, striking the employee on the nose.

Employee was burning with a torch. He was not wearing a welding jacket or apron. He was bent over a job when the oxygen line broke and saturated two layers of clothing and cutting sparks or flame ignited, causing second degree burns on abdomen and neck.

EE was rolling wire feeder towards pan. His middle finger was caught between handle and end of pan.

Employee was loosening bolts on bearing housing and a piece of metal went into his left eye.

EE was getting off forklift, conditions were wet. His gloves were wet and hands slipped where he was holding rails. He could not hold and fell on right hip. Employee started losing time on 8/26/09. **Employee started losing time again on 9/8/09.

EE was moving buckets, when he turned and walked into barmill, hitting his front teeth.

Employee was trying to break loose a part with a tool, when it broke loose, causing strain on shoulder joint.

Gradual onset of carpal tunnel syndrome due to work duties. Employee started losing time 4/10/09.

Employee had come-a-long hooked to a bracket on each side of tilt cylinder, holding it up to change out pins. Employee was using his finger as a line-up tool. The bracket broke and caught his fingers between the cylinder and hole in clevis.

Employee was pulling on pry bar. When something popped in middle of back. He started losing time 5/1/08.

Employee was grinding. He stopped and blew the dust particles off to see the job and the particles blew back around his glasses.

EE lifted cover improperly with chain hook in the hole and it would not fit in cover had already fell off once and he hooked it the same again. Then get cover in place and let the crane down, relasing tension. Cover folded and fell on his. where he was standing in front of the cover. He was knocked down and the cover landed in his leg, the hinge area striking him.

Grinding on shield caving beam and twisted back.

Hand pinned between fork and shield

Employee had his finger under bracket and hit down on the bracket, mashing finger between bracket and structure.

Employee was using slide hammer and got finger caught between slide and stop.

Employee was cutting side shield on a shield. The piece he cut off slipped out of his hand and struck his lower leg.

Gradual onset due to work duties. EE stared lose- ing time 9/8/06.

Employee was grinding burn bevels with disc grinder.

EE was holding pieces for other welder to tack and eyes received welding burn.

Cut wrist on plate being machined on #2 lathe.

CUT FINGER REMOVING SHAVINGS FROM TOOL ON LATHE.

Employee was holding a rubber hose and was cutting it off with a box blade. He cut his finger.

EE WAS DRIVING TRACKHOE OFF LOWBOY. THE DOOR OF TRACKHOE WAS OPEN AND WHEN EE STARTED OFF THE RAMP, THE DOOR CAME AROUND AND SHUT ON HIS FINGERS, WHERE HE HAD HIS HAND HOLDING ON (LACERATION TO LEFT MIDDLE FINGER).

Employee leaned over to move a shim so he could pick up cat seal under the shim and he cut his hand.

Employee was grinding a piece of metal and a stray shaving hit him in the eye. Employee was wearing eye protection at the time of the incident.

GRADUAL ONSET DUE TO WORK DUTIES. FIRST DAY AWAY FROM WORK 10/26/2005

Employee was wedging motor from power pack with pry bar and he pulled his shoulder. Employee started losing time on August 31, 2005.

Gradual onset of carpal tunnel syndrome due to normal job duties. Employee started losing time on September 8, 2005.

The part employee was working with was on a pallet. The employee stepped on the pallet and it broke causing him to twist his knee. The employee started losing time due to his injury on August 3, 2005.

Employee reached, with left hand, and grabbed roof support on fork truck. He put his left foot up on forklift and his right foot slipped on a rock or small object causing him to fall. He broke his fall by grabbing with his right hand, pulling his back.

Gradual onset of Carpal Tunnel due to normal job duties observed through work study. Medical treatment requested 3/21/05. Employee started losing time for this illness on 6/8/05.

Employee was cutting a band off container with a knife. The knife slipped and punctured his lower arm.

Employee was walking to backside of burn table and he tripped on hose and caught himself with both hands, folding hands back. EMPLOYEE STARTED LOSING TIME FROM WORK ON DECEMBER 30,2004.

EE WAS WELDING INSIDE OF CRUSHER FRAME AND A FOREIGN OBJECT FLEW IN HIS EYE.

Employee was tightening bolt on barmill with wrench.

EMPLOYEE SQUATTED DOWN TO MOVE PLATE ON FLOOR AND WHEN HE TRIED TO SLIDE THE PLATE OVER, HE HEARD HIS KNEE POP. RECEIVED MEDICAL TREATMENT BUT NOT MSHA REPORTABLE. 9/4/04 EMPLOYEE WAS STEPPING UP IN PAN. WHEN HE PUT HIS WEIGHT ON KNEE IT STRAINED HIS KNEE. RECEIVED MEDICAL TREATMENT ON 9/7/04. MSHA REPORTABLE, EXISTING INJURY.

Fan blew foreign object into right eye.

Employee prying tank over on cog, felt something pull in right shoulder and in arm.

EMPLOYEE WAS LEANING OVER AND KNOCKING STAPLES OUT OF HOSE FITTING.

EE WAS BUFFING FIT IN GEAR BOX AND GOT TRASH IN HIS EYE.

EE WAS CUTTING A PIECE OF CARBON ON BANDSAW & HE PUSHED HIS THUMB AGAINST THE SAW BLADE.

EE WAS MOVING WELDING MACHINE WIRE FEEDER. IT STARTED TO TIP OVER & THE EE REACHED TO STOP IT FROM TURNING OVER & STRAINED HIS UPPER ARM

EE WAS SETTING 2""X4""X57"" METAL PLACE. GAUGE HE WAS SETTING ON FLIPPED OVER THE METAL PIECE FELLON FINGER.

EE WAS PULLING PISTON OF ACTUATOR. OIL WAS ON THE BOTTOM SIDE AND WHEN PULLING OUT THE PISTON W/CRANE, A SUCTION ON THE PISTON WAS CREATED. THE PISTON JUMPED OUT AND THE EE'S RT.RING FINGER & MIDDLE FINGER WERE CAUGHT BETWEEN THE PISTON AND THE ACTUATOR.

EE WAS GOUGING WITH WELDING HOOD ON. TRASH BLEW UNDER HOOD AND INTO HIS EYE.

EE WAS CLEANING PARTS & PICKED UP SEAL CARRIER. THE SEAL CARRIER ON THE TABLE FELL AND HE REACHED TO CATCH IT AND IT FELL ON HIS LITTLE FINGER, LEFT HAND, CUTTING & CAUGHT FINGER BETWEEN THE TABLE & SEAL CARRIER.

EE WAS TAKING HEAVY LIFTING CHAINS OFF EQUIPMENT BEING MOVED, WHEN HE STRAINED HIS BACK.

EMPLOYEE REACHED DOWN TO TURN ON WELDING MACHINE.

EMPLOYEE WAS TAKING MOTORS OUT OF SUPPORT FRAME, PRYING WITH BAR. EMPLOYEE REQUESTED MEDICAL TREATMENT 7/30/02. HE STARTED LOSING TIME EFFECTIVE AUGUST 15, 2002.

EMPLOYEE WAS POSITIONING CHANNEL UNDER BELT TAILPIECE FOREIGN BODY WENT IN LEFT EYE.

EMPLOYEE FELT DISORIENTED, GROGGY, WOOZY AND HIS BLOOD PRESSURE WAS ELEVATED.

EE WAS USING PRY BAR AND SAID HIS LITTLE FINGER AND SIDE OF RIGHT HAND WENT NUMB.

EMPLOYEE WAS LIFTING TRACK TORCH AT HEIGHT ABOVE SHOULDERS.

EMPLOYEE WAS WORKING ON LINE PANS. HE LIFTED THE DOOR AND FELT SOMETHING PULL IN LOWER LEFT ARM.

EMPLOYEE WAS USING A HAMMER TO INSTALL BUSHING. HE HIT HIS THUMB WITH THE HAMMER AGAINST THE BAR.

EE WAS GRINDING WEAR STRIPS AND FOREIGN BODY WENT IN LEFT EYE.

EMPLOYEE WAS ROLLOING RELAY BAR TO WELD AND FELT PAIN IN LOWER BACK.

EMPLOYEE STEPPED DOWN OFF SHIELD ABOUT 20 INCHES. HIS FOOT TURNED UNDER AND HE FELL BACK FIRST ON THE GROUND, LANDING ON A SLEDGE HAMMER.

EE WAS GOUGING CLEVIS, THEN LIFTING THEM OFF SHIELD. EE STARTED LOSING TIME 11-29-01.

EE REACHED FOR TORCH, KNOCKING OFF THE TRACK TORCH AND TRIED TO GRAB THE TORCH WITH HIS HAND. HE CAUGHT HIS FINGER BENDING IT BACK. EE DID NOT REQUEST MEDICAL TREATMENT UNTIL 10-9-01.

EMPLOYEE WAS GETTING TUBS TO PUT PARTS IN AND STEPPED ON A NAIL THAT WENT IN BOOT AND FOOT.

EMPLOYEE WAS ASSEMBLING CONVEYER AND COMPLAINED OF BEING WEAK, DIZZY AND HARD TO BREATHE. IT HADBEEN DETERMINED THAT THIS ILLNESS IS WORK RELATED.

EE WAS PULLING ON JIB CRANE & FELT PAIN IN BACK AND DOWN THROUGH LEGS.

EE WAS USING A PUNCH TO MAKE A LINE TO BURN BY. PIECE OF PUNCH BROKE AND STRUCK EE IN FINGER AND HAND.

EE WAS BURNING METAL AND A FAN WAS BLOWING NEARBY SLAG PARTICLES FLEW IN CORNER OF EYE. EE WAS WEARING SAFETY GLASSES.

EE WAS DRIVING ROLL PIN IN SOCKET WHEN SOCKET SLIPPED. HE STRUCK LEFT THUMB WITH HAMMER.

EMPLOYEE WAS INSTALLING AN AIR BRAKE, WHEN THE WRENCH SLIPPED AND CUT HIS ARM. MEDICAL TREATMENT WAS NOT REQUESTED AT THIS TIME. ON SEPTEMBER 12, 2001 THE EMPLOYEE REQUESTED MEDICAL TREATMENT.

EMPLOYEE WAS SCREWING PISTON ON ROD AND CUT FINGER ON SHARP EDGE REMAINING ON PISTON.

EE WAS TAKING PIECE OUT OF BEAD BLASTER WHEN IT SWUNG ON CRANE. EE GRABBED CHAIN AND FELT PAIN IN NECK, LEFT ARM, AND HAND.

EE WAS CHECKING AND TURNING GEARS OVER.

EE WAS WELDING. A FOREIGN OBJECT FROM ANOTHER WELDER GRINDING WENT IN HIS RIGHT EYE WHEN HE RAISED HIS HOOD.

EE WAS REMOVING GEAR FROM GEAR CASE USING A BAR TO LIFT GEAR TO CLEAR WHERE IT WOULD COME OUT. HE REQUESTED MEDICAL TREATMENT 4/13/01.

EE WAS SITTING CROSS-LEGGED IN FACE PAN WELDING.

EE WAS USING A HAND HELD DISK GRINDER. GRINDING DECKS IN PANS. FINGERES WERE GOING NUMB AND WRIST WAS HURTING.

EE WAS HANDLING 1/2"" COVERS WHEN HE HURT HIS BACK.

EE WAS TAKING PILLOW BLOCK BEARING OFF PALLET ON PALLET RACK WHEN BEARING WAS REMOVED THE WEIGHT OF OTHER BEARING ON PALLET MADE PALLET FLIP OFF OF RACK. EE TRIED TO GRAB PALLET BUT WAS UNSUCC ESSFUL, PALLET PULLED FREE AND STRAINED HIS SHOULDER.

EE WAS HOLDING BAR AND ANOTHER EE STRUCK BAR WITH HAMMER. BAR KICKED UP AND STRUCK EE'S RIGHT THUMB. (REQUESTED MEDICAL TREATMENT ON 10/6).

EMPLOYEE WAS GETTING OUT OF 35 TON GROVE WITH PARTS IN HIS HAND. HE MISSED A STEP, FALLING ON HIS SHOULDER ONTO THE GROUND. (BEGAN RESTRICTED DUTIES 10/26/00)

EE WAS PULLING HAMMERS OFF CRUSHER ELEMENT WHEN BAR SLIPPED OUT OF PRESS HITTING EMPLOYEE.

EE WAS LIFTING MACHINED PLATE. PLATE SLIPPED CUTTING HAND BETWEEN THUMB AND FINGER

EE WAS WELDING INSIDE FAN, WELDING OVERHEAD. WELDING SPLATTER FELL IN COLLAR AND WENT ON DOWN INSIDE SHIRT. EMPLOYEE WAS WEARING WELDING JACKET.

EE PICKED UP A PIECE OF METAL AND DROPPED IN ON BURN TABLE. HIS FINGER WAS PINCHED BETWEEN METAL AND TABLE.